How to reset a Jeep Grand Cherokee tire?
Hold down the TPMS reset button for about five to ten seconds or until the TPMS light blinks three times, then release the button. Start the engine and drive: Start the engine and drive your Jeep for about 10 minutes at a speed of 30 mph or higher. Turn the ignition to the ON position without starting the engine. Press and hold the TPMS reset button (usually below the steering wheel) until the TPMS indicator blinks three times, then release. Drive the vehicle at speeds above 25 mph for about 10 minutes to complete the sensor relearning process.With your Jeep turned off, place the ignition key in the On position (but don’t start the car) and hold the reset button until the TPMS light blinks three times. Release the button and wait for 20 minutes; this should cause the warning light to go away. If not, there are a few other tricks you can try.Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait 20 minutes for the sensor to refresh. The tire pressure monitor reset button is usually located beneath the steering wheel.Some TPMS systems do not necessarily need the TPMS reset method or the TPMS activation tool to configure the sensor. So, you just turn the car keys on to ignite the engine and begin to drive slowly at a steady speed within the 20-30 mph range for at least 10 minutes.At AutoZone, we carry replacement TPMS sensors for most makes and models. And if you need help resetting the TPMS light, we can offer helpful advice or refer you to a shop in our professional network.
How do you reset the TPMS on a 2010 Jeep Grand Cherokee?
Drive your car at 50 mph for 10 minutes to reset the sensor. Find a place to park and turn off your car completely. Turn your key to the “On” position without turning the car back on. Press the TPMS reset button and hold until the light blinks three times. One of the most common reasons for a TPMS light staying on despite the tires being properly inflated is a sensor malfunction. TPMS sensors are typically located inside the tire and can wear out or become damaged over time, particularly if you’ve hit a curb, driven through a pothole, or been off-road.If your TPMS light is faulty, it might need to be reset. Also, if you have filled your tires with air to the optimal level, you may need to reset the system if the light on your dashboard doesn’t turn off. You can reset your TPMS light using a button inside your vehicle.Press and hold the TPMS reset button: This button is usually located under the steering wheel or in the glove box. Hold down the TPMS reset button for about five to ten seconds or until the TPMS light blinks three times, then release the button.If your TPMS warning light stays on, but your tire pressure is fine, it’s possible that one of the sensors is: Low on battery (TPMS sensors have a lifespan of about 5–10 years).
How to reset tire pressure sensor on 2014 Jeep Grand Cherokee?
Press and hold the TPMS reset button (usually below the steering wheel) until the TPMS indicator blinks three times, then release. Drive the vehicle at speeds above 25 mph for about 10 minutes to complete the sensor relearning process. Ensure all tires are properly inflated to the recommended PSI. Drive at 50 mph for 10–15 minutes on a highway or open road. Turn off the vehicle and restart it—your TPMS light should now be off.Steps to Resetting Your Tire Pressure Light Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait 20 minutes for the sensor to refresh. The tire pressure monitor reset button is usually located beneath the steering wheel.A TPMS relearn is always required when a new TPMS sensor or sensors are installed. Without pairing, or ‘relearning,’ the sensor doesn’t ‘talk’ to the Tire Pressure Monitoring System and the system simply can’t work. Programming a TPMS sensor is an additional step in TPMS service.With your Jeep turned off, place the ignition key in the On position (but don’t start the car) and hold the reset button until the TPMS light blinks three times.
Where is the TPMS reset button on a 2014 Jeep Grand Cherokee?
The tire pressure monitor reset button is usually located beneath the steering wheel. If you can’t find it, check the owner’s manual. Inflate all tires to 3 PSI over your recommended amount, then deflate them completely. Be sure to include the spare tire, as it might also have a sensor. The tire pressure monitor reset button is usually located beneath the steering wheel.
How do I reset my TPMS without the reset button?
If your vehicle doesn’t have a reset button, check the infotainment system or dashboard menu for a TPMS recalibration option. With the vehicle off, disconnect the battery for a few minutes to reset the system. Reconnect the battery and start the vehicle. Press and hold the TPMS reset button: This button is usually located under the steering wheel or in the glove box. Hold down the TPMS reset button for about five to ten seconds or until the TPMS light blinks three times, then release the button.At AutoZone, we carry replacement TPMS sensors for most makes and models. And if you need help resetting the TPMS light, we can offer helpful advice or refer you to a shop in our professional network.Press and hold the button until the TPMS warning light blinks, then release. Start the vehicle and drive for 5–10 minutes to allow the system to reset.Can I recalibrate TPMS myself, or do I need a professional? Most TPMS resets can be done at home, but if recalibration fails or sensors are faulty, a professional scan tool or dealership service may be required.
How to reset a 2018 Jeep Grand Cherokee?
Locate the button labeled “STEP” in your Jeep Grand Cherokee. Press the “STEP” button until you get to a menu screen that indicates how many miles you have left until service. Press and hold the “RESET” button. Without starting your vehicle, turn your ignition to the “ON” position. Locate the button labeled “STEP” in your Jeep Grand Cherokee. Press the “STEP” button until you get to a menu screen that indicates how many miles you have left until service. Press and hold the “RESET” button.